Abbsocket 170

High Load Performance Resin Anchor Data Sheet is based on an M20x170mm long Abbsocket with an embedment depth of 170mm in a hole 32mm diameter. Available from M16 up to M30 (dimensions are the internal thread) Application Installation of surface mounted posts for Safety fences, Environmental Barriers and similar installations. Applications where the ultimate design load does not exceed 65 kN. Description The Abbsocket used in conjunction with Abbfix resin anchor grout has been tested by a NAMAS accredited laboratory and the copy of results of testing to BS 5080 part 1 are available as evidence of test results. Designed to meet a serviceable life of not less than 20 years. The Abbsocket is a unique design solely marketed by Abbot Fixings Systems Ltd and covered by a patent. The Abbsocket is made from stainless steel (grade 316 to BS 970 Part 1), and comes complete with a 20mm stainless steel hexagon set bolt (grade A4/80 to BS 6105), and a stainless steel washer (grade 316 to BS 1449 Part 2). Abbsockets are installed into the concrete so that each socket is flush with the concrete surface. The post baseplate unit is then secured with hexagon headed bolts. Abbsockets are designed for applications where a removable fixing head is required and because of the short length of drilled hole, Bridgedeck waterproofing systems are protected and the Sealing of voids in the anchorage's is a result of using the Abbfix resin system. The sleeve length of the Abbsocket is 60mm with an internal thread length of 40mm, which allows for the adjustment of the hexagon set bolt. Base plates with a bedding mortar gap of 10-25mm can be fixed with the standard fixing. On request longer hexagon set bolts can be fitted prior to delivery and Galvanised packing washers supplied as accessories if required. Other accessories in the form of Nylon 6.6 tophat washers are available as insulators between the stainless and galvanised components. Special long anchors can be made to meet below ground applications.

Features Stress free fixing allows minimum edge distances and anchor spacing. No close edging between fixing and hole sides ensures good resin bond and vibration resistant anchorage. 32mm X 170 mm hole required maximum tolerance 36mm diameter. Torque maximum 120Nm Minimum thickness for Nylon 6.6 insulating washers 3mm. Minimum thread engagement in Abbsocket 20 mm. Resin is moisture tolerant and coloured grey. Longer embedment lengths are available providing increased loads. Suitable for C20 concrete. Packing washers and high flow bedding mortar available to Highway specification. Performance Tensile load in kN 0.2mm SLIP 049.20 1.0mm SLIP 070.03 Failure 104.40 Tests carried out in C20 Concrete. Actual strength at time of test 24.0 N/mm2. These results were provided from testing to BS 5080 carried out by a NAMAS ACCREDITED Laboratory for Abbot Fixing Systems Ltd

Technical Services On Site Testing Service to BS5080 Part 1 For further information please contact our sales office. Fixing Procedure Drilling 32mm x 170mm Drilling should be carried out by using rotary percussive equipment. If diamond drilling is required where steel reinforcement is present, then the hole must be under-reamed or roughened. Cleaning of Holes All holes should be clear of dust and debris, by using a compressed air lance or blow-out bulb in addition to wire brushing. Mixing of Resin The ABBSOCKET should be used in conjunction with ABBFIX Resin Anchor Grout, mixed according to the instructions on the pack. Installation To ensure complete encapsulation, it is recommended that the resin is poured into the hole prior to the installation of the ABBSOCKET. Push the ABBSOCKET down into the resin with a twisting action. Important Note To the best of our knowledge and belief, the information contained in this leaflet is true and accurate, but as conditions of use and any labour involved are beyond our control, it is the responsibility of the customer to satisfy himself that this product is fit for the purpose for which he intends to use it, and no responsibility can be accepted, or warranty given by our company.

For further information telephone on 01908 511730